Hayward pump filter hook up

Begin by ensuring that the cartridge is securely installed. Recognize which hole is for inflow lower and which is for outflow upper. When connecting the hose ends, ensure that they are going into the proper connectors before securing them. Normally, these hoses will be protected by hose clamps that you can manually tighten with a screw or a self-tensioned clamp.


  1. speed dating for seniors in edmonton.
  2. Pool Filters | In Ground Swimming Pool Filters - Hayward Pool Products!
  3. Install an Above-Ground Pool Pump in 5 Steps | inafythenfar.tk.

To keep from cracking or damaging the hose, do not over-tighten the clamp. Finally, make sure that your filter pumps power supply is grounded as it should be. Keep in mind that even with a filter, you will still have to manually clean your in-ground pool—especially if it is located by a lot of trees or bushes. Separate the valve from the pipe and lateral assembly. Also make sure the 10 laterals at the end of the pipe are rotated up. They have to be in their up position to fit through the hole in the top of the tank. These laterals are somewhat fragile.

How To Install a Pool Sand Filter

Ensure that none are cracked or broken. Place the pipe and lateral assembly inside the tank. Step 8 After the lateral assembly is inside, carefully rotate the 10 laterals 90 degrees in their down position. Step 9 Make use the pipe is centered in the opening. Tape the top of the pipe to prevent sand from entering and clogging the laterals.

Step 10 The sand filter package comes with a cardboard sand shield. Place this over the pipe and within the opening. Step 11 Pour sand carefully into the pool sand filter until laterals are fully covered. For this unit 3 bags should leave at least 6" space between the top of the sand and the top of the filter. Level sand as you pour and make sure the center pipe remains centered in the opening. Be careful when leveling the sand that you do not lift the pipe and lateral assemble up off the bottom of the tank.

You will not be able to push the pipe back down without causing the laterals to rotate up. Step 13 Remove tape from top of pipe. Slip the Multiport control valve onto the central pipe - check the O-ring to ensure it is positioned correctly.

Step 14 Install clamp around the tank and valve flange. Loosely tighten clamp so that the valve can be rotated on the tank for final positioning. Step 15 The next step is to connect the "PUMP" port of the multiport valve to discharge side of pump. You will need to screw a straight thread adapter purchased at a hardware store into the "PUMP" port. To help seal this connection wrap two layers of Teflon tape the adapters. Do not over tighten or you cause the joint to fail.

How to Hook Up a Swimming Pool Filter

Step 17 Cut a short piece of pipe and glue it to the adapter. Make sure the pipe and inside of the adapter are clean. Gluing is a two-step process. First apply a thin but even coat of purple primer on each surface to be joined: After the primer dries, apply a thin even coat of glue to both surfaces. Wait 30 seconds for the glue to set. Step 18 Glue on a union to facilitate future maintenance on the pool sand filter or pump.

Support Center

In years you will have to disconnect the multiport valve from the tank to change the filter sand. A union will save you from having to cut it out of the piping. Step 19 Screw another adapter into the discharge side of the pump then add piping and elbows required to connect the filter and pump ports. In a basic system this connection will probably be to the Chlorinator. Also add a union to this line for future maintenance.

This picture does not show the water hose. Step 22 Tighten multiport valve flange clamp with a screwdriver. Tap around the clamp with the screwdriver handle as you are tightening the clamp to help seat the clamp properly.

How To Use Different Pool Filter Valve Settings

Place vinyl protector caps over the ends of the screws. ProGrid vertical grid diatomaceous earth DE filters provide superior water clarity, efficient flow and large cleaning capacity for unparalleled filtration.

Hayward offers a full line of multiport and slide backwash valves to support our complete line of vertical grid DE and sand filters. Utilized industry wide, Hayward backwash valves set the standard for performance and reliability. Designed to work with vertical grid DE filters, with 80 square feet of filtration area, the ProGrid DE Separation tank is ideal for water conservation and savings during backwashing by returning chemically treated backwash water to the pool.

Opening Your Pool | Pool Maintenance | Support - Hayward Pool Products

ProSeries top-mount and side-mount sand filters utilize a precision engineered umbrella-fold self-cleaning lateral system to provide efficient flow and evenly distributed water for long lasting performance. With all the ProSeries advanced features, ProSeries Plus filters are designed to meet the needs of the most demanding applications including large residential and semi-commercial pools, in-floor cleaning systems, solar heating systems and water features.


  • hook up vcr to imac.
  • Opening Your Pool;
  • vida dating reviews.
  • stanley bailey planes dating?
  • Select Your Region:?
  • How to Hook Up a Sand Filter Pump to an Above Ground Swimming Pool.
  • The S filter combines high-rate filtration performance with the durability of a corrosion proof, heavy duty, injection molded tank. Perflex extended-cycle diatomaceous earth DE filters provide superior water clarity and extended filter cleaning cycles without requiring backwashing. Your session is about to timeout due to inactivity.

    Click OK to extend your time for an additional 30 minutes.